PNP Convergence VTOL Aircraft

VTOL PNP Convergence

The Convergence vertical takeoff aircraft has a simple design with a delta wing and three brushless motors – two rotating motors on the wings and one fixed motor on the rear. It is equipped with flight control software specially tuned by its creator, Mike McConville. This software allows the transition between drone and airplane flight simply with the help of a switch. It also offers Stability and Acro flight modes to allow you to discover all its performances. This model is even ready to receive FPV equipment with integrated supports to accommodate a camera and a video transmitter.

Contoured and Simple
Unlike other vertical take-off C models on which the entire wing pivots and which require no less than 4 motors, the Convergence is equipped with a simple but profiled delta wing and three brushless motors – two rotary motors on the wing and a fixed engine at the tailplane.

In drone flight, the motors installed on the wing pivot to a vertical position to provide thrust and control for takeoff. In airplane flight, the motors installed on the wing pivot to a horizontal position and the elevons of the role model control the tilt angles. In airplane flight, yaw is controlled by the differential thrust of the wing motors.

Simplicity with new flight control software
The model is equipped with flight control software tuned by Mike McConville, so almost any RC pilot can experience vertical takeoff flight.

Automatic Transition
To switch from drone flight to airplane flight, all you need to do is flip a switch. The flight controller will rotate the wing motors into position and activate or deactivate the tail motor depending on the transition.

Stability and Acro flight mode
These two flight modes allow you to enjoy many flight characteristics.

- Stability Mode
In drone flight, Stability mode offers you limits on tilt angles and allows you to restore the stability of the model when you release the sticks. You'll be able to take off and land like a pro, even if you're flying a drone for the first time. In airplane flight, you will also have the limits of bank angles and the model will self-stabilize when you release the sticks.

If you use Stability mode when transitioning between drone and airplane flight, it will maintain the attitude from one phase to the other to ensure you have the best possible vertical takeoff flight experience.

- Acro Fashion
In Acro mode, there are no limits on tilt angles or self-stabilization. In drone flight, the model flies like a standard drone by tilting according to the direction. It can also flip and rotate like other drones.

In airplane flight, Acro mode allows you to perform aerobatic figures. Thanks to the forward thrust of the two brushless motors, you will have power and speed. You can use differential thrust to do spins.

Ready for FPV flight
This ROLE model is designed to accommodate the majority of cameras most used in FPV. There is a camera compartment under the nose and space to install a video transmitter on the rear of the model. The simplicity of access will allow you to install the hardware in minutes.

Simple transmitter and receiver setting
The Plug-N-Play version is compatible with all transmitters with at least 6 channels. You can use either a standard receiver with normal servo connection or a serial receiver. Simply connect the receiver to the model's flight controller. No complex programming is necessary. You can use the channel 5 O switch for selecting Stability or Acro modes and the channel 6 O switch for transitioning between airplane and drone flights.

General characteristics

- Versatility of a drone and the agility of an airplane
- Design by pilot Mike McConville
- Exclusive flight controller software to simplify your flights
- Stability and Acro modes
- Powerful brushless motors for incredible performance
- Simplicity of setting the transmitter
- Ready for FPV flight with camera and video transmitter slots
- Wing surface: 1883 cm²
- Receiver: DSMX/DSM2 Receiver (Installed) BNF Basic
- Minimum 6 channel receiver (required) PNP)
- Recommended battery: Li-Po 3S 11.1V 2200-3000mA
- Transmitter required: 6 channels minimum compatible with DSMX/DSM2 (BNF Basic)
- 6 channels minimum (PNP)
- Level: Intermediate
- Recommended flight range: Outdoor

Required items

- Minimum 6 channel transmitter
- Receiver 6 channels minimum
- 3S 2200-3000mA Li-Po battery (EFLB22003S30 recommended)
- 3S compatible Li-Po charger

Recommended FPV equipment – all items sold separately

- Spektrum 650TVL CCD NTSC FPV Camera (SPMVC650)
- Spektrum 25mW 5.8GHz video transmitter (SMPVT025)
- Power adapter (SPMA9556)
- Spektrum 4.3” video monitor with glasses (SPMVM430C)